CC2 Zapper from ParaZapper

CC2 zapper Specifications

The ParaZapper™ CC2 is a microprocessor based multi-frequency zapper designed with improved results in consideration. One frequency alone does not provide the best overall coverage for multiple types of micro-organisms. Two frequencies can double the chance of hitting a particular organisms resonance, but even this does not provide the best coverage. For that reason, we have selected a total of 29 frequencies in several modes, including Rife (Mode 1 and 4) frequencies along with Clark Zapper frequencies (mode 2) and Croft's Terminator Zapper (Mode 3) frequencies, a special 2500 Hz mode, and a MX mode. The frequencies are as follows.

While we like and appreciate these Recent ParaZapper review videos from customers on YouTube,
We do not necessarily agree with everything that is said in them.

Video review of ParaZapper CC2

ParaZapper CC2 powerful and excellent output

ParaZapper CC2 very accurate frequency

How to use the ParaZapper CC2 and what the indicators show

ParaZapper CC2 very good accuracy

Why are multi frequencies important?

The one real reason is that there is not any single "one frequency" that works for everything. There are some better frequencies that appear to be better than others in producing a Clark spectrum but it actually takes over 40 base frequencies to get almost all of the microbes listed in the Clark frequency list. Even then, it should be noted that the Rife frequency list completely disagres with the Clark frequencies. For this reason, we provide some of both.

What about high duty cycles that some claim are better?

While some sellers claim that having a duty cycle that is higher that 66 percent will produce the even harmonics. This is a misguided interpretation and is completely false except for 1 specific setting. When the duty cycle is exactly 2 to 1, then there will be an exact set of frequencies that includes both the even and odd harmonics but it should be noted that each will only be part strength because. Additionally, if the duty cycle is not just right, the frequencies can actually interfer with each other and actually reduce effectiveness. If you buy a unit with a high duty cycle, make sure that it is microprocessor based such as ParaZapper UZI for accuracy because having the exact frequency makes all the difference.

When observed under the microscope, the electrical current appears to explode almost all of the micro-organisms present.

Prices and Buy CC2 Now

Includes instructions for operation.

MODE	Frequencies	Duration
Mode 1	Rife 2.0 - 2.7 kHz range Set 1 Freq 1 2280 +/- 10 Hz Most units are +/- 4 Hz Freq 2 2128 +/- 10 Hz Most units are +/- 4 Hz Freq 3 2489 +/- 11 Hz Most units are +/- 4 Hz Freq 4 2008 +/- 10 Hz Most units are +/- 4 Hz This mode covers a broad range and is general purpose. Mode 1 will blink the Mode/Battery LED 1 Flash every 2 seconds You may use this for 60 minutes on, 1 time daily, but, using it for 30 minutes, repeat 3 times should produce better results. Note: Use for 7.0 to 28 minutes on, 15-20 minutes off, repeat 3 times. Repeating 4 times will improve effectiveness. Note: Since each frequency lasts for 7.0 minutes, 7 minutes will only provide the first 2 frequencies. It takes 28 minutes to get all eight frequencies. Note that due to the accuracy of the microprocessor generated signal, most units are within 4 Hz of the specified frequency but the guaranteed accuracy is +/- 11 Hz. To use frequency set 2 to first, Presss and hold the mode switch while turning the power on.	7.0 min 7.0 min 7.0 min 7.0 min
Mode 2	Clark 30 kHz range provides a range of frequencies Freq 1 29800 +/- 100 Hz Freq 2 29365 +/- 100 Hz Freq 3 30255 +/- 100 Hz Freq 4 33280 +/- 100 Hz Stop and off 5 seconds, 3 - 1 second pulses and repeat Mode 2 will blink the Mode/Battery LED 2 Flashes every 2 seconds You may use this for 60 minutes on, 1 time daily, but, using it for 30 minutes, repeat 3 times should produce better results. Note: Use for 30 minutes on, 15-20 minutes off, repeat 3 times. Repeating 4 times will improve effectiveness. Note that due to the accuracy of the microprocessor generated signal, most units are within 50 Hz of the specified frequency.	7.0 min 7.0 min 7.0 min 7.0 min
Mode 3	Croft Terminator range Freq 15.2 Hz +/- 0.2 Hz Stop and off 5 seconds, 3 - 1 second pulses and repeat Mode 3 will blink the Mode/Battery LED 3 Flashes every 2 seconds Note: Use for 7 minutes on, 15-20 minutes off, repeat 3 times. Repeating 4 times will improve effectiveness. Important Note: This is a very low frequency that will feel much stronger than the others if the electrodes come into contact with the body. The signal is actually not any stronger, it just feels stronger due to normal nerve physiology. However, due to this sensitivity, it is strongly advised to keep this frequency away from accidental contact with either the chest area near the heart, or the head area, including the jaws and neck and especially keep it away from the eyes.	7.0 min
Mode 4	Rife 660-880 Hz range Set 1 Freq 1 728 +/- 6 Hz Most units are +/- 3 Hz Freq 2 787 +/- 6 Hz Most units are +/- 3 Hz Freq 3 800 +/- 6 Hz Most units are +/- 3 Hz Freq 4 880 +/- 6 Hz Most units are +/- 3 Hz Repeats frequencies continuously. Rife Broad Range general purpose covers the most important frequencies. Mode 4 will blink the Mode/Battery LED 4 Flashes every 2 seconds You may use this for 60 minutes on, 1 time daily, but, using it for 30 minutes, repeat 3 times should produce better results. Note: Use for 30 minutes on, 15-20 minutes off, repeat 3 times. Repeating 4 times will improve effectiveness. Note: Since each frequency lasts for 7.0 minutes, 7 minutes will only provide the first frequency. It takes 56 minutes to get all eight frequencies. Note that due to the accuracy of the microprocessor generated signal, most units are within 3 Hz of the specified frequency but the guaranteed accuracy is +/- 6 Hz.	7.0 min 7.0 min 7.0 min 7.0 min
Mode 5	2.5 kHz Mode Set 1 Freq 1 2500 +/- 10 Hz Most units are +/- 4 Hz Freq 2 2503 +/- 10 Hz Most units are +/- 4 Hz Freq 3 2505 +/- 10 Hz Most units are +/- 4 Hz Freq 4 2508 +/- 10 Hz Most units are +/- 4 Hz Freq 5 2511 +/- 10 Hz Most units are +/- 4 Hz Freq 6 2514 +/- 10 Hz Most units are +/- 4 Hz Freq 7 2496 +/- 10 Hz Most units are +/- 4 Hz Freq 8 2492 +/- 10 Hz Most units are +/- 4 Hz Freq 9 2489 +/- 10 Hz Most units are +/- 4 Hz Freq 10 2486 +/- 10 Hz Most units are +/- 4 Hz Repeats cycle Mode 5 will blink the Mode/Battery LED 1 long flash and 1 quick flash every 2 seconds You may use this for 70 minutes on, 1 time daily, but, using it for 70 minutes, repeat 3 times should produce better results. Note: Use for 7.0 to 70 minutes on, 15-20 minutes off, repeat 3 times. Repeating 4 times will improve effectiveness. Note: Since each frequency lasts for 7.0 minutes, 7 minutes will only provide the first frequency. 14 minutes will provide 2 frequencies It takes 70 minutes to get all 10 frequencies. Note that due to the accuracy of the microprocessor generated signal, most units are within 4 Hz of the specified frequency but the guaranteed accuracy is +/- 11 Hz.	7.0 min 7.0 min 7.0 min 7.0 min 7.0 min 7.0 min 7.0 min 7.0 min 7.0 min 7.0 min
Mode 6	MX Mode Set 1 MX mode has 8 special frequencies between 2000 Hz and 2500 Hz. Provides Broadest range of coverage. Repeats sequence Mode 6 will blink the Mode/Battery LED 1 long flash every and 2 quick flashes 2 seconds You may use this for 60 minutes on, 1 time daily, but, using it for 60 minutes, repeat 3 times should produce better results. Note: Use for 30 minutes or 60 minutes on ( 7.5 minutes for each frequency ), 15-20 minutes off, repeat 3 times. Repeating 4 times will improve effectiveness. Note: Since each frequency lasts for 7.5 minutes, 7.5 minutes will only provide the first frequency. 30 minutes provides 4 frequencies. It takes 60 minutes to get all eight frequencies. Note that due to the accuracy of the microprocessor generated signal,	7.5 min
	Note: The frequencies in this unit are far more accurate than the frequencies in Rife units that select the frequency using a dial, unless a digital readout is used.

This unit has an automatic timing mode and recycling for each frequency range, but it does not feature an automatic shutdown so that it can be used for continuous zapping. Power to the unit is supplied by a standard 9-volt battery and is controlled by a push-on / push-off switch. Frequency and mode selection are by momentary contact push button switch. To change modes, simply press the mode switch. The battery and mode LED's will both come on at the same time. Release the switch and the next mode will start. To change to the next mode, simply press the [Mode] switch again.

Description of Indicators ( Status, Mode/Battery ) and switches (ON/OFF) and Mode (mode change)

Power ON switch: (ON/OFF Button)
When the ON/OFF switch is pressed, the unit will come on and always starts out in Mode 1.

Status LED: (Status) located nearest the On/Off button
The status LED can be used to monitor normal operation and also to test the unit for correct operation. The Status LED will normally appear yellowish or orange but there are exceptions. If the battery is completely dead or missing, the LED will be off or dark. If for some reason, the output fails, the LED will either be solid green or red.
To test the unit when operating, the unit should be on and operating with the copper paddles connected but not touching. In this condition, the LED will appear yellow or amber because it is flickering between red and green. A Red Status may indicate that the paddles are shorted together, however, if the red and green are not shorted, a completely red Status means that you need to contact the factory for service.
Touching the copper paddles together should cause the LED to show almost completely red due to the current load being pulled by the short circuit. This is an indicaton that the zapper output is functioning properly and providing sufficient output for best results.

Mode change switch: ( MODE button )
To use Automatic mode, press and hold the Mode button while turning the unit on.
The Battery/Mode LED will show Red, release the button, and you will be in the Automatic Mode.

When the unit is first turned on, it starts in Mode 1 each time.
Pressing this [Mode] button at any time will change the current mode and will also restart the timer.
Each time that the [Mode] switch is pressed, it will cycle to the next mode which can be observed by watching the Mode/Battery LED for the number of flashes produced.

The Mode/Battery LED will flash the number of the Mode it is in every 2 seconds.

1 Flash = Mode 1
2 Flashes = Mode 2
3 Flashes = Mode 3
4 Flashes = Mode 4
1 Long Flash followed by 1 quick flash = Mode 5
1 Long Flash followed by 2 quick flashes = Mode 6

Mode LED: (Battery / Mode) which is the Lower LED
The mode LED flashes the corrosponding number of flashes for the mode that it is currently operating in as described in the Mode table above.

Which frequency?

Mode 1 has four Rife frequencies that have been in use for many years and may be the best frequency to use first. It is equivalent to the 2000 Hz / 2500 Hz Clark frequency range as well as the Rife frequencies that are present.

Mode 2 (30 kHz range) is the normal Clark frequency but the other frequencies may have some advantages.

Mode 3 (15 Hz) may provide the best overall penetration but there are some limitations to its use.

Mode 4 is the Rife 600-880 Range ( four main rife frequencies that are commonly used ). These frequencies should kill most any microbe over time, according to published Rife frequency lists. This range is also best for uses such as zappicating where Dr. Clark recommended 1kHz or 1000 Hz.

Mode 5 is the 2500 Hz Wobble mode ( 10 frequencies at about 2500 Hz ).

Mode 6 is the MX mode ( 8 frequencies between 2000Hz and 2500 Hz ).

Disclaimer: All statments and claims above are made in relation to killing microbes in water, such as protozoa, bacteria, fungi, algae, etc.

Please read all information and disclaimers before buying these products.

Positive offset as specified by Dr. Clark
Yes, CC Stabilized output on all ParaZapper™ models.
Better Multi Frequency zapper 2.128 kHz to 2.489 kHx Rife mode ( 4 frequencies),
30 kHz (4 Frequencies), 15 Hz (Terninator frequency),
727-880 (Rife - 4 frequencies), 2.5 kHz mode, and the MX mode.
Better Zapper Made in the USA of high quality parts .
Better Top quality wires and plugs, more compact
Solid wire connections, no rinky-dink alligator clips.
Good battery life: Status Indicator, Mode indicator, Low Battery LED
Instructions for water treatment.
Information booklet available separately.
Ruggedly built for long lasting reliability.
Some competitors models are cheaply built.
Best Zapper Price, Quality, Reliability, Performance .
Battery included.

$ParaZapper\99 CC2 with copper paddles and pads.$

One ParaZapper ™ CC2 with
copper paddles and pads for $239.00 US plus S+H.

$2 each ParaZapper\99 CC2 with copper paddles and pads.$

Two ( 2 ) each ParaZapper ™ CC2 with
copper paddles and pads for $445.00 US plus S+H.

$5 each ParaZapper\99 CC2 with copper paddles and pads.$

Five ( 5 ) each ParaZapper ™ CC2 with
copper paddles and pads for $1080.00 US plus S+H.

$ParaZapper\99 CC2 with copper paddles.$

One ParaZapper ™ CC2 with
copper paddles for $209.00 US plus S+H.

There is additional information such as comparison charts, testimonials, and videos in the menu above.

AUDIO
Warning: Although Hulda Clark claimed her zappers could not reach internal organs, including the intestines, she did not use the advanced multi-frequency ParaZapper including the 4 point contact and 3 points positive. Since these devices demonstrate greater effectiveness in inactivating microbes like bacteria. protozoa, and fungi, and some individuals have chosen to use these ParaZappers for off-label personal use on their bodies, we have noted reports of doing so may destroy much of the natural, beneficial flora in the intestines. For at least one reason, it is very important to replace your microbiome with supplemental probiotics soon after using. Generally, consuming a good yogurt containing live and active cultures of at least 5 or 6 strains of bacteria will be helpful in any respect. The company does not endorse any off-label use but believes ethical companies should let the public know about potential issues involving off-label uses.

Previous models of Hulda Clark Parasite Zapper, formerly available on paradevices and petzapper sites and since not as advanced as these models, those were considered to be superior to the other competing devices.

The following statement is true for All zappers, regardless of where purchased, not just ParaZapper.

Notice: On advice of counsel, here as well as elsewhere, sites are required to inform you that the statements and claims on this site have not been evaluated by the FDA ( Food and Drug Administration ) and are not intended to diagnose, treat, cure or prevent any disease -- not for use on humans or with pets. These easy to use battery powered devices are not offered or intended for human use and are not to diagnose or prescribe for medical or psychological conditions nor to claim to prevent, treat, mitigate or cure any conditions, nor to recommend specific products as treatment of disease or to provide diagnosis, care, treatment or rehabilitation of individuals, or apply medical, mental health or human development principles. The devices discussed herein have not undergone evaluation and/or testing by the United States FDA ( Food and Drug Administration ) or like agency of any other country. Risks which might be determined by such testing are unknown. The information on this site is not a substitute for medical or veterinary advice.

Additional Notice: These zappers are sold only for the experimental use of killing microbes in water. Any other usage is considered to be off-label and such usage is at the discretion of the user. They are not a Medical device and are not represented as such.

Hulda Clark ParaZapper sales
5537 Balboa Ct.
Pinson, AL 35126 USA

Please e-mail us at: email1 sales at huldaclarkparazapper.com
or email2 sales at paradevices.com

We are having telephone problems. The calls often go to voice mail too quickly and we are having a problem getting the messages.
Also, the quarantine for coronavirus has left us with no one to answer the telephone Please contact us by e-mail

Phone: 205-856-3909
866-765-5116
Phone Hours: 9:30 AM to 3:00 PM Central Time

Please Note that we do not sell by telephone but are happy to talk to you. Email is much better as: If inquiring about an order, please include the order number / Invoice Number that should start with HCPZ ( do not add HCPZ to a number The HCPZ is part of the correct number ), The transaction number is different and not in our system.

EFAX = NO, we do not accept E-faxes due to possible risks.

Accept Credit Cards Online

N.L.

Zapper