Zapper

Zapper

6-pack Hulda Clark Zapper

6-Pack Zapper with 6 modes and 14 frequencies

100 percent positive offset
Multiple frequencies
Accurate frequencies and good waveforms

Rugged and Reliable zapper
Quality workmanship
Easy to use - Made in the US

6-Pack Specifications

The ParaZapper™ 6 Pack is a basic microprocessor based multi-frequency zapper designed with improved results in consideration. It is the low end unit of the ParaZapper line of products but still far better than the competition. One frequency alone does not provide the best overall coverage for multiple types of micro-organisms. Two frequencies can double the chance of hitting a particular organisms resonance, but even this does not provide the best coverage. For that reason, we have selected a total of 14 separate frequencies in several modes, including Rife (Mode 2 and 5) frequencies along with Clark Zapper frequencies (mode 1) and Croft's Terminator Zapper (Mode 3) frequency, 1000 Hz (Mode 4), and 10,000 Hz ( mode 5 ) frequency. The frequencies are as follows.

Why are multi frequencies important?

The one real reason is that there is not any single "one frequency" that works for everything. There are some better frequencies that appear to be better than others in producing a Clark spectrum but it actually takes over 40 base frequencies to get almost all of the microbes listed in the Clark frequency list. Even then, it should be noted that the Rife frequency list completely disagres with the Clark frequencies. For this reason, we provide some of both.

What about high duty cycles that some claim are better?

While some sellers claim that having a duty cycle that is higher that 66 percent will produce the even harmonics. This is a misguided interpretation and is completely false except for 1 specific setting. When the duty cycle is exactly 2 to 1, then there will be an exact set of frequencies that includes both the even and odd harmonics but it should be noted that each will only be part strength because. Additionally, if the duty cycle is not just right, the frequencies can actually interfer with each other and actually reduce effectiveness. If you buy a unit with a high duty cycle, make sure that it is microprocessor based for accuracy because having the exact frequency makes all the difference.

Important! While the 6 Pk can be use 7 minutes on, 20 minutes off routine that was originally suggested by Dr. Clark in any mode, it is not suggested as it has been found that in modes 1,2,and 5, the 6 pk2 works better when used in the continuous mode. Follow the timing suggested in the mode that you select to use.

"ParaZapper 6PK, with paddles"
Customer's video review of New ParaZapper 6-Pack
Please note that while the customer thinks that this unit may be of use as a personal fitness device, we do not advertise or sell it for that purpose.
ParaZapper 6-Pack, very good Accuracy Proven
MODE Frequencies Duration
Mode 1 Clark 30 kHz range
Freq 1 30250 +/- 300 Hz
Freq 2 29800 +/- 300 Hz
Freq 3 30720 +/- 300 Hz
Cycle and repeat

Mode 1 will blink the Mode/Battery LED 1 quick Flash every 2 seconds

You may use this for 60 minutes on, 1 time daily, but,
using it for 30 minutes, repeat 3 times should produce better results.
Repeating 4 times will improve effectiveness.

Note: Since each frequency lasts for 7.0 minutes, 7 minutes will only provide only the first frequency.
It takes 21 minutes to get all three frequencies.

Note that due to the accuracy of the microprocessor generated signal,
most units are within 100 Hz of the specified frequency.

7.0 min
7.0 min
7.0 min












Mode 2 Rife 2.0 - 2.7 kHz range
Set 1
Freq 1 2489 +/- 25 Hz
Freq 2 2127 +/- 20 Hz
Freq 3 2280 +/- 20 Hz
Freq 4 2008 +/- 20 Hz
Cycle and repeat

Mode 2 will blink the Mode/Battery LED 2 quick Flashes every 2 seconds

You may use this for 60 minutes on, 1 time daily, but,
using it for 30 minutes, repeat 3 times should produce better results.
Repeating 4 times will improve effectiveness.

Note: Since each frequency lasts for 7.0 minutes, 7 minutes will only provide only the first frequency.
It takes 30 to 31 minutes to get all four frequencies.

Note that due to the accuracy of the microprocessor generated signal,
most units are within 10 Hz of the specified frequency but the guaranteed accuracy is +/- 1 percent of the specified frequency.


7.0 min
7.0 min
7.0 min
7.0 min















Mode 3 Croft Terminator range
Freq 15.2 Hz +/- 0.2 Hz
Cycle and repeat

Mode 3 will blink the Mode/Battery LED 3 quick Flashes every 2 seconds

Note: Use for 7 minutes on, 15-20 minutes off, repeat 3 times.
Repeating 4 times will improve effectiveness.

Important Note: This is a very low frequency that will feel much stronger than
the others if the electrodes come into contact with the body. The signal is actually
not any stronger, it just feels stronger due to normal nerve physiology. However, due
to this sensitivity, it is strongly advised to keep this frequency away from accidental
contact with either the chest area near the heart, or the head area, including the jaws
and neck and especially keep it away from the eyes.

7.0 min












Mode 4 1000 Hz range
Freq 1000 Hz +/- 10 Hz
Cycle and repeat

Mode 4 will blink the Mode/Battery LED 4 quick Flashes every 2 seconds

Note: Use for 7 minutes on, 15-20 minutes off, repeat 3 times.
Repeating 4 times will improve effectiveness.

7.0 min






Mode 5 Rife 660-880 Hz range
Freq 1 727 +/- 7 Hz
Freq 2 787 +/- 8 Hz
Freq 3 800 +/- 8 Hz
Freq 4 880 +/- 9 Hz
Repeats frequencies continuously.

Mode 5 will blink the Mode/Battery LED 1 long flash and 1 quick Flash every 2 seconds

You may use this for 60 minutes on, 1 time daily, but,
using it for 30 minutes, repeat 3 times should produce better results.
Repeating 4 times will improve effectiveness.

Note: Since each frequency lasts for 7.0 minutes, 7 minutes will only provide only the first frequency.
It takes 30 to 31 minutes to get all four frequencies.

Note that due to the accuracy of the microprocessor generated signal,
most units are within 5 Hz of the specified frequency but the guaranteed accuracy is +/- 1.0 percent of the specified frequency.


7.0 min
7.0 min
7.0 min
7.0 min














Mode 6 10000 Hz range
Freq 10000 Hz +/- 100 Hz
Cycle and repeat

Mode 6 will blink the Mode/Battery LED 1 long flash followed by 2 quick flashes every 2 seconds

Note: Use for 7 minutes on, 15-20 minutes off, repeat 3 times.
Repeating 4 times will improve effectiveness.


7.0 min






Note: The frequencies in this unit are far more accurate than
the frequencies in Rife units that select the frequency using a dial,
unless a digital readout is used.

This unit has automatic recycling for each frequency range, but it does not feature an automatic shutdown so that it can be used for continuous zapping. Power to the unit is supplied by a standard 9-volt battery and is controlled by a push-on / push-off switch. Frequency and mode selection are by momentary contact push button switch. To change modes, simply press the mode switch. The battery and mode LED's will both come on at the same time. Release the switch and the next mode will start. To change to the next mode, simply press the [Mode] switch again.

Description of Indicators ( Status, Mode/Battery ) and switches (ON/OFF) and Mode (mode change)

Power ON switch: (ON/OFF Button)
When the ON/OFF switch is pressed, the unit will come on and always starts out in Mode 1.

Status LED: (Status) located nearest the On/Off button

The status LED can be used to monitor normal operation and also to test the unit for correct operation. The Status LED will normally appear yellowish or orange but there are exceptions. If the battery is completely dead or missing, the LED will be off or dark. If for some reason, the output fails, the LED will either be solid green or red.
To test the unit when operating, the unit should be on and operating with the copper paddles connected but not touching. In this condition, the LED will appear yellow or amber because it is flickering between red and green. A Red Status may indicate that the paddles are shorted together, however, if the red and green are not shorted, a completely red Status means that you need to contact the factory for service.
Touching the copper paddles together should cause the LED to show almost completely red due to the current load being pulled by the short circuit. This is an indicaton that the zapper output is functioning properly and providing sufficient output for best results.

Mode change switch: ( MODE button )

To use the Automatic Cycle Mode, press and hold the Mode button while turning the unit on.
The Battery/Mode LED will show Red, release the button, and you will be in the Automatic Mode.

When the unit is first turned on, it starts in Mode 1 each time.
Pressing this [Mode] button at any time will change the current mode and will also restart the timer.
Each time that the [Mode] switch is pressed, it will cycle to the next mode which can be observed by watching the Mode/Battery LED for the number of flashes produced.

The Mode/Battery LED will flash the number of the Mode it is in every 2 seconds.

1 Flash = Mode 1
2 Flashes = Mode 2
3 Flashes = Mode 3
4 Flashes = Mode 4
1 Long Flash followed by 1 quick flash = Mode 5
1 Long Flash followed by 2 quick flashes = Mode 6

Mode LED: (Battery / Mode) which is the Lower LED
The mode LED flashes the corrosponding number of flashes for the mode that it is currently operating in as described in the Mode table above.

Which frequency?

Mode 1 (30 kHz range) is the normal 30,000 Hz Clark frequency but the other frequencies may have some advantages. This mode should be at least 3 times as good as regular 30 kHz Clark zappers due to the three frequencies provided.

Mode 2 has four Rife frequencies that have been in use for many years and may be the best frequency to use first. It is equivalent to the 2000 Hz / 2500 Hz Clark frequency range as well as the Rife frequencies that are present.

Mode 3 (15 Hz) may provide the best overall penetration but there are some limitations to its use.

Mode 4 (1000 Hz) was originally intended for use with the food zappicator which is now known not to work.

Mode 5 is the Rife 727-880 Range ( four main rife frequencies that are commonly used ). These frequencies should kill most any microbe over time, according to published Rife frequency lists.

Mode 6 (10000 Hz) is common in the Rife frequency list.

 
 
Disclaimer: All statments and claims above are made in relation to killing microbes in water, such as protozoa, bacteria, fungi, algae, etc.

ParaZapper 6-Pack with copper paddles.


Quantity:  - 
One ParaZapper ™ 6-Pack
( 6 zappers in 1 ) with
copper paddles
for $137.00 US plus S+H.


ParaZapper 6-Pack with copper paddles and pads.


Quantity:  - 
One ParaZapper ™ 6-Pack
( 6 zappers in 1 ) with
copper paddles and pads
for $186.00 US plus S+H.


ParaZapper 6-Pack with copper paddles and 3-M straps.


Quantity:  - 
One ParaZapper ™ 6-Pack
( 6 zappers in 1 ) with
copper paddles and 3-M straps
for $176.00 US plus S+H.


ParaZapper 6-Pack with 4 horse pads.


Quantity:  - 
One ParaZapper ™ 6-Pack
( 6 zappers in 1 ) with
4 horse pads
for $192.00 US plus S+H.



Warning: Although Hulda Clark claimed her zappers could not reach internal organs, including the intestines, she did not use the advanced multi-frequency ParaZapper including the 4 point contact and 3 points positive. Since these devices demonstrate greater effectiveness in inactivating microbes like bacteria. protozoa, and fungi, and some individuals have chosen to use these ParaZappers for off-label personal use on their bodies, we have noted reports of doing so may destroy much of the natural, beneficial flora in the intestines. For at least one reason, it is very important to replace your microbiome with supplemental probiotics soon after using. Generally, consuming a good yogurt containing live and active cultures of at least 5 or 6 strains of bacteria will be helpful in any respect. The company does not endorse any off-label use but believes ethical companies should let the public know about potential issues involving off-label uses.

Previous models of Hulda Clark Parasite Zapper, formerly available on paradevices and petzapper sites and since not as advanced as these models, those were considered to be superior to the other competing devices.

The following statement is true for All zappers, regardless of where purchased, not just ParaZapper.

Notice: On advice of counsel, we are required to inform you that the statements and claims on our web site have not been evaluated by the Food and Drug Administration and are not intended to diagnose, treat, cure or prevent any disease -- not for use on humans or with pets. These battery powered devices are not offered or intended for human use or to diagnose or prescribe for medical or psychological conditions nor to claim to prevent, treat, mitigate or cure any conditions, nor to recommend specific products as treatment of disease or to provide diagnosis, care, treatment or rehabilitation of individuals, or apply medical, mental health or human development principles. The devices discussed herein have not undergone evaluation and/or testing by the United States Food and Drug Administration or like agency of any other country. Risks which might be determined by such testing are unknown. The information on this site is not a substitute for medical or veterinary advice.

Additional Notice: These devices are sold only for the experimental use of killing microbes in water. Any other usage is considered to be off-label and such usage is at the discretion of the user. This is not a Medical device and is not represented as such.


Hulda Clark ParaZapper sales
490 Holland Rd. Unit B
Horton, AL 35980 USA

Phone: 205-856-3909
866-765-5116
Phone Hours: 9:30 AM to 3:00 PM Central Time

Please Note that we do not sell by telephone but are happy to talk to you.

We are having telephone problems. The calls often go to voice mail too quickly and we are having a problem getting the messages.

You may e-mail us at: email1
or email2

We often have 20 to 30 calls a day at 5 to 20 minutes each, and just can not answer them all without missing shipments.

If inquiring about an order, please include the order number / Invoice Number starting with HCPZ, The transaction number is different and not in our system.

EFAX = NO, we do not accept E-faxes due to possible risks.

...
Accept Credit Cards Online